hello, a note. you have 2 tubes behind your back that should be cut off. there the line can hang from the rescue parachute. or line with a full stall. it can also happen that if you fall forward the tube hurts your head. just meant as a hint. regards
Good point; that was already my plan. I just need to move my electrical control box down the frame somewhere.
1 Like
Hi, Thank You
I decided on the impress 3 because it is the best of the quality. Although it is 1 kg heavier than the current pod harness of this class, only the best material is used. From the geometry it is possible to fly exactly the same setting of the scales as with thermal flight in mountains. the container underneath the pilot is therefore perfect for the battery. the shape is optimal to save electricity. it also works with other pod harness. but the most important point is now why i love impress 3 so much … there was a competion pod which is already prepared for the rescue parachute. aerodynamically integrated in front of the pilot and with area for the flight instruments. there are motors from geiger, rotex, hacker that are designed for eppg from europe. there are also similar engines in china. However, I haven’t seen anyone today that is comparable in performance with European engines. it is the same with the esc. Here are leading companies from Germany and Czech. There are folding propellers for Geiger motors that Toni Roth makes in Germany. you can buy them. all other eppg pilots, like me, build their own propellers themselves. but i think e-props will soon bring a folding propeller with 125 cm / 130 onto the market.
My project came to an end today. I got my motor controller back from APD, installed it in the frame, powered it up, and shortly after I started spinning the prop at low throttle the controller shorted internally and burst into flame. It was completely destroyed, along with two batteries (didn’t ignite but the labels are burned off so I presume the cells are heat damaged) and likely my motor as well.
I could probably rebuild this but I’ve dumped enough money into this project that I’m just done with it. After watching that controller go from fine to full-on inferno in seconds, I don’t want to be anywhere near that thing in flight. I’m just disappointed that I never got to see if it would actually fly.
I feel you ! Sorry to see that…I was wondering if that esc should not have some protection ? I don’t know what to say… Regards
I know that feeling. My own project is in the very back of the garage after a catastrophic failure (poorly designed cage pushed through the prop on launch).
Commiserations, Paul
I’m sorry for what happened to you!
below I would like to list a few technical things.
very often you can see similar examples if rc material is used for drives that are too large and burn. not by the current in the drive itself. the esc switches off the much too high phase currents. (if the motor is undersized and the propeller is too large, phase currents will already occur at half throttle of several hundred amperes in the esc). the drive is still rotating and generates a few kilowatts of power which then come back into the esc and bring everything to melt in a few milliseconds and it burns. Therefore esc suitable for aviation have always programmed an active freewheel so that there is no problem with recuperation. Even if you put together the wrong setup for aviation esc, there is no fire because the esc automatically detects it long before an overload occurs and then a fault occurs. if you do it 3 times, it will not start. then only the manufacturer can unlock the esc. this serves the safety of the user if he does not have enough expertise about electric drives.
2 Likes
This ESC has all of those features; active freewheeling, and bus and phase current limiting. I sent the ESC back to APD to fix a problem with the current measurement in the logging. They did test it before it left their shop, but I suspect that something wasn’t assembled quite right in the ESC after the repair and the vibration from the motor and propeller caused something to come loose and bridged some contacts internally to cause the short. It wasn’t your typical pop + smoke ESC failure. This was a VERY energetic electrical fire.
APD has offered to replace the controller, but as I said before I’m just not interested in continuing the project. I’m hoping that I can at least get a refund from them so I can recoup a little bit of what I’ve spent. That controller was the single most expensive component on the whole machine.
Big bummer. Do not think about it for a moment, grab a few beers and perhaps after some days the damage appears less than you think now.
Here is the other half of me abandoning this project:
Originally I decided to build this because I was sick of having to drive 4+ hours round trip every time I wanted to go flying. All of the closest free flight sites to me are a two hour drive. However, over the course of the winter I figured out how to fly the mountain behind my house. Now I can do a hike-and-fly that takes me 1 hour, from door to door. I don’t even have to pack up my wing; I can land, rosette, and walk right to my house. It is also proving to be a fairly reliable site with multiple flyable days a week. So I really don’t need this motor for my original intended purpose anymore. Honestly my real interest has always been free flying and soaring; the motor was just a subsitute. I don’t think I need the substitute anymore.
1 Like
Just posting a quick update to say that APD refunded me what I paid for the motor controller ($989) so at least it wasn’t a total loss. I sent the motor back to Neumotor to be inspected and it checked out, so no damage there. If anyone is looking for a cheap jumping-off point for a project I’ll sell the 8057/75 motor, motor mount plate, prop adapter, 2" prop extension, and two 38x12" carbon propellers for $350. I think I paid around $760 for all that stuff.
Can you send a picture of the motor, interested to see the design.
Very interesting thread! Thanks for sharing your experiences. I also had an APD HV pro ESC burn last year. Lucky I was on the ground!!! My eppg was strapped with a load cell to a post of my house. Scared the crap out of me and my family when it burned. It was a serious fire that I put out with a fire extinguisher. Batteries puffed but didn’t burn as the wires melted off the ESC and stopped the short.
Since then I’ve been successfully flying with the MAD M40 C30 using a flyer 400a Esc (had flyer Create some firmware to lower the acceleration curve to suit larger props). 125cm prop and 18s. I get 20 mins from 6kg of lipo’s in still air.
Cool. I recently received a mad M40. What thrust are you getting with yours?
The original lighter M40C30 version 59kg thrust on 18S using 3 times Turnigy 16ah 12C packs and H30F prop R-EZ-04-2 / A2 And Flyer 400A ESC with modified firmware for lower acceleration.
The temp of motor seemed fine until I put a temp probe right into the windings. After 3 minutes at 50+ kg the windings get to 100C. They quickly cool once throttling down. 59kg is more than enough thrust for me so it’s quite usable but temp could be a limitation for heavy climbs and or heavy wing loading. The Flyer 400A ESC doesn’t get hot and seems good for the price but you don’t get any data from it.
The second M40 C30 https://mad-motor.com/product/mad-torq-m40-c30-pro-kv43/
I also have this one but haven’t had time to test it.
Ok cool. I have that bigger one. I was hoping it would keep cooler than the small one. Haven’t gotten around to testing though.
2 Likes
Sorry if I can’t read a so long topic…I’m very interesting in @bratwurst wonderfull project (powered advance harmess), but i can’t understand an aspect: If you install an engine in the back-bag of the free-fly harness, during the fly, the weight of the engine will load on your shoulders…Is it tollerable ?
I mean: the biggest difference between the freefly and the powered fly are the paramotor’s arms, wich unload the weight of the engine, but they make you lose the feeling of your wing. How is it possible to solve this compromise ?
the easiest way is to read postings from people who have been building eppg for thermals for years. you can find them on facebook and partly on youtube. here in this forum it would be wrong to give an explanation of how to properly build eppg for thermals the topic here is about the openppg project.